Difference between revisions of "Icom IC-7600"

Revision as of 20:16, 31 October 2017

The Icom IC-7600 covers the 160 to 6 meter amateur bands. It utilizes IF-DSP technology and selectable roofing filters at 3kHz, 6kHz and 15kHz. Like the IC-7700 and IC-7800, the IC-7600 uses dual 32-bit floating-point Texas Instruments DSP chips with one for the radio and the other for the spectrum scope. This display is a 5.8 inch color WQVGA LCD.

Status: Currently on the market as of 2017, still in production. Replaces the Icom IC-756 Family of transceivers.

• Receive Range 1: 0.030-60.000 MHz
• Receive System: Single receiver
• Dual Watch: Yes
• Roofing Filter Capability: Yes
• Roofing Filter Bandwidth: 15/6/3kHz
• Third Order Intercept (IP3): Over 30 dBm
• Transceiver Input Voltage: 13.8 Vdc
• Transceiver Maximum Current: 23.0 A
• Antenna Ports: 2
• Computer Connection Type: USB or CI-V interface
• Digital Mode Audio Input/Output: USB or 8-pin DIN
• Voice Synthesizer Capability: Yes
• Radio Dimensions: Width 13.375", Height 4.563", Depth: 11.000"
• Weight: 22.000 lbs.
• SSB/CW Maximum Power: 100 W
• SSB/CW Minimum Power: 2 W
• AM Maximum Power: 30 W
• AM Minimum Power: 1 W

Ver.2.00 Firmware

Tip: The first time you update, thoroughly read the Section 14 (UPDATING THE FIRMWARE) of the IC-7600’s instruction manual and information for firmware 2.00 on Icom Co. Support page. The firmware can be updated using a USB-flash drive.

Some new features:

• point and click the mouse for Click-and-Listen receiver control.
• Waterfall screens
• additional functions added to the spectrum scope
• APF AF Level setting
• CI-V commands for antenna control, logging software and RIT/DELTA-TX
• TX Delay (HF/50M) settings for variable delay time
• Standby setting to remotely turn ON the IC-7600 using the REMOTE jack.
• MOS-FET is now the default value of SEND Relay Type

MARS / Extended Transmit and Receive

MARS/CAP Mod: IC-7600

RX Frequency Coverage Expansion

• remove D52, D53, D54, and D55

TX Frequency Coverage Expansion

• remove D56, D57, D58, and D59

offers: 1.6 - 30MHz and 51 - 54 MHz

5MHz Band Operation

• remove D62

offers: 5.255 - 5.405 MHz

Non-Icom Amplifier Connection

The ALC input level must be in the range 0 V to – 4 V. The transceiver does not accept positive volt-age. SEND RELAY type menu item (in the ACC set mode menu) which allows selection of the OMR-109F relay (LEAD) or a MOSFET interface (MOS-FET). The MOSFET option is rated at 250V/0.2A AC/DC, non-inductive. If the amplifier's open-circuit keying-line voltage is above 16V but below 250V, this option can be selected.

ACC set mode

Send Relay Type: Selects the switching relay type for [RELAY] from Lead and MOSFET. Select the suitable relay type when connecting a non-Icom linear amplifier.

• Lead - Use mechanical relay. (16 V DC/0.5 A max.; default)
• MOS-FET - Use semiconductor type relay. (250 V/200 mA max.)

Menu: SET -> ACC -> SEND Relay Type

The IC-7600 can key an amplifier circuit up to 250Vdc at 200 mA, select the correct keying mode via the ACC set menu.

With the Firmware Update Version 2.00 “MOS-FET” is now the default value of “SEND Relay Type.”

Use with SB-200 / SB-221 Amplifier

So, theoretically, you can use the IC-7600 with your old Heathkit amplifier without the Harbach Soft-Key interface as long as you use the MOS-FET ACC mode. However, you are better off if you go ahead and install the Soft-Key interface. If you have the Soft-Key interface installed, thus reducing the key line to approximately 0.7VDC at 1.5mA, then you will want to use the Lead ACC mode.

The recommended configuration: Use Harbach Electronics SK-220 Soft-Key Keying Interface and on the Icom ic7600 ACC set mode = Lead.

Accessories

• LDG M-7600 External Meter