Predictable Network Interface Names

or, why my interfaces are no longer called eth0 and eth1 etc... and I cant ifup and ifdown anymore, nor can I 'service network restart.'

Is this crap actually an improvement?

The classic naming scheme for network interfaces applied by the kernel is to simply assign names beginning with "eth0" and ethX after that. A problem occurs on new distributions with driver probing on every boot. On every boot the darn things do driver probing now to check to see if you made any hardware changes. The driver probing does not always assign interfaces with the same numbers. A system with two nics might have nic 1 as eth0 today and eth1 tomorrow even if you did not make any changes. Rather than trying to figure out why the driver probing is inconsistent, the devs used a band-aide and completely changed the name schema.

systemd - The change can be blamed on systemd. systemd is a new init system and system manager, that was adopted by most of Linux distributions now over the traditional SysVinit manager.

Predictable Network Interface Names - out with the old ethX naming schema and in with this new weird looking names like 'enp3s0' or 'enp0s10'. Now undev assigns names to ethernet devices incorporating Firmware/BIOS provided index numbers, and etc.

If you want to bring down your interface, and you identified it as 'enp3s0' as an example, issue the command:

ifconfig enp3s0 down

Interfaces are named following rules that use information from the firmware and bios if available.

The commands ifdown and ifup read the file /etc/network/interfaces on SysV machines. Either the scripts are not configured or are not compatible with systemd, since distributions like Ubuntu don't bother with them.

1. Names incorporating Firmware/BIOS provided index numbers for on-board devices (example: eno1)
2. Names incorporating Firmware/BIOS provided PCI Express hotplug slot index numbers (example: ens1)
3. Names incorporating physical/geographical location of the connector of the hardware (example: enp2s0)
4. Names incorporating the interfaces's MAC address (example: enx78e7d1ea46da)

enp3s0:
| | |
v | |
en| |   --> ethernet
  v |
  p3|   --> bus number (3)
    v
    s0 --> slot number (0)

A program for providing detection and configuration for systems to automatically connect to networks. Network management framework (daemon and userspace tools) - A GUI thing.

Network Manager has a command line tool that can be used to see which interfaces it is controlling. Pull up a terminal window and type the following command:

nmcli dev status

sample output:

# nmcli dev status
DEVICE  TYPE      STATE      CONNECTION         
enp0s4  ethernet  connected  Wired connection 1 

For Ubuntu and Mint distributions (recent like 18.3 or 19.2) this is how network interfaces are configured. Network Manager settings are controlled by the configuration file: /etc/NetworkManager/NetworkManager.conf

To disable Network Manager for a specific interface: Tell Network Manager to stop controlling an interface is by adding the following lines to the /etc/NetworkManager/NetworkManager.conf file:

[main]
plugins=keyfile

[keyfile]
unmanaged-devices=mac:00:11:22:33:44:55;mac:66:77:88:99:00:aa

Completely disable Network Manager so it does not control anything, even after reboot:

This seems to be the Redhat recommended way

sudo systemctl stop network-manager
sudo systemctl mask network-manager

This seems to be the Debian/Ubuntu/Mint recommend way

sudo stop network-manager
echo "manual" | sudo tee /etc/init/network-manager.override

Command Line:

The command:

sudo service NetworkManager restart

Will not restart your network service, it only restarts the networkmanager. Connection will not be interrupted by issuing this command.

The command:

systemctl --all|grep -i network

With systemd various '*.service' and '*.target' init scripts/config files are used to describe services, and you can see them running this way.

nmcli

NetworkManager from the command line.

nmcli – a command-line tool used to configure networking.

nmtui – a simple curses-based text user interface, which is also used to configure and manage newtwork interface connections.

Other tools include the nm-connection-editor, control-center, and network connection icon (all under GUI).

Usage:

nmcli [OPTIONS] OBJECT { COMMAND | help }

By default mint calls the first network connection (wired) as "Wired connection 1". We will use this in our examples. You can rename the interface.

Commands

nmcli dev status
nmcli con show
nmcli con show Wired\ connection\ 1
nmcli con show -a
nmcli con down Wired\ connection\  1
nmcli con up Wired\ connection\  1

You can use nmcli to configure the interfaces, change settings, and more with additional commands.

There seems to be inconsistencies in how the command line parameters work from Redhat based distributions as compared to Debian based distributions. Your mileage may vary.