PC Power Supply Voltage Data and Connector Types

PowerSupplyVoltageDataforPersonalComputers08.jpg

Power for Internal Peripheral Devices

Four Pin Molex Power Connector

Molex Drive Connector
Typically used for 5¼ drives such as CD Rom and DVD Drives. Used for legacy IDE, EIDE, and ATA Hard Drives.

Pin Wire Color Signal
1 Yellow +12v
2 Black Ground
3 Black Ground
4 Red +5v

Four Pin Molex Connector01.png

 

Serial ATA Power Connector

PowerSupplyVoltageDataforPersonalComputers03.png

 

Berg Floppy Power Connector

AMP 171822-4
Typically used for 3½ floppy disk drives.

BergFloppyPowerConnector.png

 

Six Pin PCI Express Power Connector

PCI Express GFX Connector
MOLEX 39-01-2060

PowerSupplyVoltageDataforPersonalComputers04.png

 

Three Pin Molex KK Type Connector

Typically used for internal cooling fans.

PowerSupplyVoltageDataforPersonalComputers05.png

 

Motherboard Power Connector Types

The eight power supply form factors are:

  1. PC / XT
  2. AT/Desk
  3. AT/Tower
  4. Baby AT
  5. LPX
  6. ATX
  7. NLX
  8. SFX

Standard ATX Connectors

Three common ATX power to motherboard connector configurations, a 20 pin connector, a 20 +4 pin connector, and a 24 pin connector. The 20 +4 may be used for either 20 pin connector motherboards or 24 pin connector motherboards. The first 20 pins are a consistent standard on all three configurations.

20 Pin ATX Power

The 20-pin Main power connector is standard for all power supplies conforming to the ATX and ATX12V 1.x form factors, and consists of a Molex Mini-Fit, Jr. connector housing with female terminals. For reference, the connector is Molex part number 39-01-2200 and the terminals are part number 5556.

PowerSupplyVoltageDataforPersonalComputers06.png

The total power handling capacity of this connector is only 251 watts, which is lower than many systems need today.

20+4 Pin ATX Power

MOLEX 39-01-2240

204ATXPowertoMotherboardConnector.png

24 Pin ATX Power

PowerSupplyVoltageDataforPersonalComputers07.png

As a general rule of thumb +/-5% is considered OK for voltage variation.

Technical Notes

Using a 24 pin power connector on a 20 pin motherboard

The 24 pin male power connector can also be used on a 20 pin motherboard by allowing the four extra to hang off the side, given there is room (one one motherboard example a capacitor is in the way.)

Using a 20 pin power connector on a 24 pin motherboard

Technically this is also possible to do, however, you risk overloading the 20 pin connector. It is possible to do this because the additional 4 connectors on a 24 pin power connector supply additional voltage to the motherboard into common circuits. Without the additional 4 connectors, you will be drawing more power than the maximum rating through the 20 pin connector which will cause it to overheat.

PowerSupplyVoltageDataforPersonalComputers11.png

A Closer Look at the Extra 4 Power Supply Pins

The 4-pin +12V power connector is specified for all power supplies conforming to the ATX12V form factor, and consists of a Molex Mini-Fit, Jr. connector housing with female terminals. For reference, the connector is Molex part number 39-01-2040 and the terminals are part number 5556. This is the same style of connector as the ATX Main power connector, except with fewer pins.

PowerSupplyVoltageDataforPersonalComputers13.png

Hot-Starting and ATX Power Supply Not Connected to a Motherboard

The old AT style power supplies could easily be turned on when not connected to a motherboard because the switch was mechanical. ATX power supplies are electronically switched via the motherboard. It is possible to turn on an ATX power supply when not connected to a motherboard.

To turn on an ATX power supply not connected to a motherboard short between the green and black wires on the 20 or 24-pin connector, with a paper clip or piece of wire.

PowerSupplyVoltageDataforPersonalComputers12.png

You can use any of the black "ground" wires. There is a single green wire you must use for the jumper. While the jumper is connected the power supply should turn on and it will remain on as long as the jumper is connected. Once the jumper is removed then the power supply will turn off.

 

Legacy AT Motherboard Power Connector

The original PC starting in 1981 used two cables (Molex 90331) to connect the power supply to the motherboard. They connected side by side into the motherboard, and they could easily be reversed accidentally, or inverted which will result in damage to the motherboard. When connecting them to the motherboard it was important to observe the "black to black" rule.

Pinout
Pin number Wire color Description
1 orange power good
2 red +5 volts or connector key
3 yellow +12 volts
4 blue -12 volts
5 black ground
6 black ground
1 black ground
2 black ground
3 white -5 volts
4 red +5 volts
5 red +5 volts
6 red +5 volts

On an AT system the power supply delivered a majority of power at 5 volts since most of the motherboard ran at that voltage. One rail was 5v and the other 12v.

PowerSupplyVoltageDataforPersonalComputers15.png

 

Additional Motherboard Power and CPU Power

Six Pin Inline Auxiliary Power Connector

ATX 2.02/2.03 and ATX12V 1.x Auxiliary Power Connector
When more amperage is required by the motherboard before the 24 pin connector was devised, this six pin inline connector was equipped with power supplies to provide supplemental power to the motherboard.

PowerSupplyVoltageDataforPersonalComputers10.png

The total power handling capacity of this connector is 58 watts. When combined with the 20 Pin ATX motherboard power connector the total power delivery capability to the motherboard is 309 watts maximum.

Eight Pin CPU Power Connector

MOLEX 39-01-2080
Required connector for modern dual CPU motherboards

PowerSupplyVoltageDataforPersonalComputers01.png

 

AMP ATX 12v Power Connector

AMP 1-480424-0
4 pin connector for the Intel Pentium 4 CPU

PowerSupplyVoltageDataforPersonalComputers02.png

 

Additional Charts and Data

Power Connector List With Introduction Chronology

Version Introduction date Included connectors
PC 1981
  • original PC main power cables
  • 4 pin peripheral cable
ATX 1995
  • 20 pin main power cable
  • 4 pin peripheral cable
  • floppy cable
ATX12V 1.0 2000
  • 20 pin main power cable
  • 4 pin 12 volt cable
  • 6 pin auxiliary cable
  • 4 pin peripheral cable
  • floppy cable
ATX12V 1.3 2003
  • 20 pin main power cable
  • 4 pin 12 volt cable
  • 6 pin auxiliary cable
  • SATA cable
  • 4 pin peripheral cable
  • floppy cable
ATX12V 2.0 2003
  • 24 pin main power cable
  • 4 pin 12 volt cable
  • 6 Pin PCI Express power cable
  • SATA cable
  • 4 pin peripheral cable
  • floppy cable
EPS12V 2003
  • 24 pin main power cable
  • 8 pin 12 volt cable
  • 6 Pin PCI Express power cable
  • SATA cable
  • 4 pin peripheral cable
  • floppy cable
PCI Express 2.0 2007
  • 24 pin main power cable
  • 4 pin 12 volt cable
  • 8 pin 12 volt cable
  • 6 Pin PCI Express power cable
  • 8 Pin PCI Express power cable
  • SATA cable
  • 4 pin peripheral cable
  • floppy cable

 

Connector Picture Chart

Connector-Picture-Chart.jpg

 

Inside the ATX Power Supply

PowerSupplyVoltageDataforPersonalComputers16.png

The power supply can be fully discharged by connecting the black and red wires together.

 

Front Panel Header Connectors

The most common question might be, which is positive, the white or the colored wire? For the LED connectors, the colored wire is usually indicative of a positive polarity.

+ colored wire
- white

Mobofrontpanelconnectors01.jpg

For the power LED indicator, insert the connector with the colored wire into the header with the '+' mark. If you've connected it the other way around, you won't see the LED light up when the system is powered. Also observe the proper polarity when connecting the hard drive LED connector.

Mobofrontpanelconnectors02.png

For the power switch connector, polarity isn't really important. The same holds true for the reset connector.

When you connect the speaker, you should observe proper polarity. Some motherboards have built-in buzzers and as such, the speaker connection is not needed.

+ red
- black

 

 

Last modified on 30 November 2016, at 12:21