Difference between revisions of "Kenwood TM-701A"
(→Modifications) |
|||
| Line 11: | Line 11: | ||
* transmitting and receiving from 136-175MHz | * transmitting and receiving from 136-175MHz | ||
* prevent intermittent memory loss due to pulses on the CPU interrupt line | * prevent intermittent memory loss due to pulses on the CPU interrupt line | ||
| + | |||
| + | ===Extended Transmit=== | ||
| + | 1 Disconnect the power and antenna. | ||
| + | |||
| + | 2. Remove the top and bottom cover. | ||
| + | |||
| + | 3. Remove knobs from front panel and the nuts from the mic and channel switch. | ||
| + | |||
| + | 4. Remove 4 screws holding the front panel and the 3 screws on the control board. | ||
| + | |||
| + | 5. Locate the green jumper wire sticking out the front panel, behind the VFO button | ||
| + | |||
| + | 6. Cut the green jumper and tape the edges to prevent them from shorting. | ||
| + | |||
| + | ===Cross Band Repeat Mod=== | ||
| + | Perform steps 1 - 6 above and continue... | ||
| + | |||
| + | 7. Optional: Install diodes D207 & D209 on control board X57-3350-00. | ||
| + | |||
| + | 8. Solder a jumper to the foil side of the TX-RX board as shown in drawing. | ||
| + | |||
| + | 9. Reassemble the radio. | ||
| + | |||
| + | 10. Reset the microprocessor (Press and hold [MR] while turning on the | ||
| + | power). | ||
| + | |||
| + | ===CROSS BAND OPERATING PROCEDURE=== | ||
| + | Turn on the Repeater mode- | ||
| + | #Press and hold [F] and then press [DUP]. | ||
| + | #Then Press [F} longer than 1 Second. The F indicator will blink. | ||
| + | #Press[LOW]. Three dots should appear in the display when the mode is on. | ||
| + | |||
| + | Turn off | ||
| + | #Press [VFO]. | ||
==Online Resources== | ==Online Resources== | ||
Revision as of 20:23, 5 February 2017
Operating dual band on 2-meter and 70-cm ham radio bands, this transceiver is very compact and features 20 memory channels and multi-scan functions. It has the same chassis as Kenwood TM-231a/431a series and shares many of the accessories.
Contents
Options
Review
Basic Usage
Programming
Modifications
Available modifications:
- cross-band repeater
- transmitting and receiving from 136-175MHz
- prevent intermittent memory loss due to pulses on the CPU interrupt line
Extended Transmit
1 Disconnect the power and antenna.
2. Remove the top and bottom cover.
3. Remove knobs from front panel and the nuts from the mic and channel switch.
4. Remove 4 screws holding the front panel and the 3 screws on the control board.
5. Locate the green jumper wire sticking out the front panel, behind the VFO button
6. Cut the green jumper and tape the edges to prevent them from shorting.
Cross Band Repeat Mod
Perform steps 1 - 6 above and continue...
7. Optional: Install diodes D207 & D209 on control board X57-3350-00.
8. Solder a jumper to the foil side of the TX-RX board as shown in drawing.
9. Reassemble the radio.
10. Reset the microprocessor (Press and hold [MR] while turning on the power).
CROSS BAND OPERATING PROCEDURE
Turn on the Repeater mode-
- Press and hold [F] and then press [DUP].
- Then Press [F} longer than 1 Second. The F indicator will blink.
- Press[LOW]. Three dots should appear in the display when the mode is on.
Turn off
- Press [VFO].
