Zastone KT-8900 Mini Dual Band Transceiver
QYT KT-8900
also known as:
Zastone KT8900, QYT KT-8900, QYT KT8900 136-174/400-480MHz Mini Mobile Radio Transceiver, Juentai JT-6188
Function:
- Dual Band VHF:136-174MHz UHF:400-480MHz
- Step Frequency 5KHz, 6.25 KHz, 10 KHz ,12.5 KHz, 15 KHz, 25 KHz
- CTCSS / DCS / 5Tone / 2Tone / DTMF
- High/Low Transmitted Power 25W/20W(VHF/UHF)
- 200 Channel Memory
- Phase lock step
- Operating Volts: 13.8V DC±15%
- Frequency Stability: ±2.5ppm
- Operating Temperature: -20~+60
- Dimension(W x H x D): 98(W) x 35(H) x 118(D)mm
- Weight: 408g
Manufacturer propaganda: JT-6188 is the 2015 new product , the world’s smallest dual band mobile radio , Its output power is 20w at VHF , and 15w at UHF ,and have 200 channels . This radio is very easy to install on cars ,and motorcycles.
Review
The KT8900 is rated at 20-25W. A 13.6VDC power supply used when not mobile. There is a defunct menu option for Audio Scrambler, the option does nothing. The radio comes with a full function keypad style microphone. Functions include: Menu, Up, Down, A/B, Exit, Reverse, Scan and Lock. The RJ-45 microphone jack has the same pin output as the Kenwood.
For computer program it requires Prolific Driver 3.2.0.0 or compatible, it is a prolific chip cable, not a standard USB cable.
Due to the fact that the Chinese suck at English translation, the Monitor button reads MOM, rather than MONI. Some other annoyances include a lack of an external Speaker jack. The port in rear is for a programming cable only. There is no 2.5 kHz stepping which makes entry of some UHF frequencies difficult.
Programming
For channel name assignments, you must program the memory for the frequency, then go back into the channel name mode, enter the name (note: mic buttons much faster than trying to spin the knob on this), and then give it the memory number to assign the name to.
Program instructions for repeater use:
set radio to VFO MODE by pressing [V/M] Press [Exit A/B] to put radio in Top or Bottom freq use top freq as RX freq and Bottom Freq as TX freq.
1 - push exit A/B XXX XXX (RX) 2 - push exit A/B XXX XXX (TX) 3 - push exit A/B back to top 4 - [Menu] 1 step freq [menu] [up] to 25.00k [menu] 5 - [up]#13 T-CTCS [menu] [up] 131.8 [menu] 6 - [up] #36 [menu] 001 (key 001 ) [menu] 7 - [up] #37 [menu] 199 (key 199 ) [menu] 8 - [up] #38 [menu] [up] + [menu] <------ this is your freq offset + - simplex area. 9 - [up] #39 [menu] key in 05000 [menu] 10 - [exit A/B] to exit the menu programing 11 - [exit A/B] lower TX freq (XXX XXX ) 12 - menu #39 [Menu] offset key in 05000[menu] 13 - [down] #38 [menu] [up] + [menu] <----- this is your freq offset + - simplex area. 14 - [down] #36 [menu] key in 001 for your channel [menu] 15 - [down] #13 [menu] make sure proper tone is there 131.8 16 [V/M] up down key to channel 1 and key up repeater ! this should work if not let me know
citation: http://www.brickolore.com/2015/05/qyt-kt8900-dual-band-mobile.html
