Difference between revisions of "Baofeng UV-B6"
| Line 1: | Line 1: | ||
==programming== | ==programming== | ||
===repeater offset and CTCSS=== | ===repeater offset and CTCSS=== | ||
| + | In this example will enter a 70cm repeater with PL and +5Mhz offset. | ||
| + | offset + or - | ||
| + | # Enter the VFO Mode | ||
| + | # Set offset [MENU] and arrow to item 21 (SFTP) | ||
| + | # Press [AB/ENTER] use arrow to select + and press [AB/ENTER] and [MENU], [MENU] to save | ||
| + | |||
| + | offset amount | ||
| + | # Press [MENU] and arrow to item 22 (OFFSET) | ||
| + | - Press [AB/ENTER] then enter the offset | ||
| + | - Press [AB/ENTER] and [MENU], [MENU] to save | ||
| + | |||
| + | |||
| + | Enter 'TCODE' (CTCSS / DCS) | ||
| + | |||
| + | - Press [MENU] , then (channel knob) to Menu 12 (TCODE) | ||
| + | - Press then [MENU] to select CTCSS / DCS / OFF | ||
| + | - Press (channel knob) to select desired code. | ||
| + | - Press to save. | ||
| + | - Press [MENU] or any key to exit. | ||
| + | |||
| + | #Enter Frequency | ||
| + | |||
| + | - Using the keypad, enter he desired frequency. | ||
| + | - Press & Hold the [VM/SCAN] button to display channels 01-99 | ||
| + | - Press (channel knob) to select the desired channel. | ||
| + | |||
| + | NOTE: If channel number is blinking, that channel has been previously programmed and will be overridden. | ||
| + | |||
| + | - Press to save. | ||
| + | |||
| + | Enter the MR Mode | ||
| + | |||
| + | - Press [VM/SCAN] to enter MR (channel mode). | ||
== External Resources == | == External Resources == | ||
* [http://www.miklor.com/UVB5/UVB5-ProgMem.php] | * [http://www.miklor.com/UVB5/UVB5-ProgMem.php] | ||
Revision as of 17:49, 22 November 2015
programming
repeater offset and CTCSS
In this example will enter a 70cm repeater with PL and +5Mhz offset.
offset + or -
- Enter the VFO Mode
- Set offset [MENU] and arrow to item 21 (SFTP)
- Press [AB/ENTER] use arrow to select + and press [AB/ENTER] and [MENU], [MENU] to save
offset amount
- Press [MENU] and arrow to item 22 (OFFSET)
- Press [AB/ENTER] then enter the offset - Press [AB/ENTER] and [MENU], [MENU] to save
Enter 'TCODE' (CTCSS / DCS)
- Press [MENU] , then (channel knob) to Menu 12 (TCODE) - Press then [MENU] to select CTCSS / DCS / OFF - Press (channel knob) to select desired code. - Press to save. - Press [MENU] or any key to exit.
- Enter Frequency
- Using the keypad, enter he desired frequency. - Press & Hold the [VM/SCAN] button to display channels 01-99 - Press (channel knob) to select the desired channel.
NOTE: If channel number is blinking, that channel has been previously programmed and will be overridden.
- Press to save.
Enter the MR Mode
- Press [VM/SCAN] to enter MR (channel mode).
