Difference between revisions of "Baofeng UV-B6"
From Free Knowledge Base- The DUCK Project: information for everyone
(→programming) |
|||
| Line 4: | Line 4: | ||
offset + or - | offset + or - | ||
| − | # Enter the VFO Mode | + | #Enter the VFO Mode |
| − | # Set offset [MENU] and arrow to item 21 (SFTP) | + | #Set offset [MENU] and arrow to item 21 (SFTP) |
| − | # Press [AB/ENTER] use arrow to select + and press [AB/ENTER] and [MENU], [MENU] to save | + | #Press [AB/ENTER] use arrow to select + and press [AB/ENTER] and [MENU], [MENU] to save |
offset amount | offset amount | ||
| − | # Press [MENU] and arrow to item 22 (OFFSET) | + | #Press [MENU] and arrow to item 22 (OFFSET) |
| − | + | #Press [AB/ENTER] then enter the offset | |
| − | + | #Press [AB/ENTER] and [MENU], [MENU] to save | |
| + | PL / CTCSS | ||
| + | #Press [MENU] and arrow to item 12 (TCODE) | ||
| + | #Press [AB/ENTER] then enter the frequency in Hz | ||
| + | #Press [AB/ENTER] and [MENU], [MENU] to save | ||
| − | Enter | + | Enter and Save to channel |
| − | + | #key in desired frequency such as 442.400 for example | |
| − | + | #Press and hold [VM/SCAN] until voice says MEMORY CHANNEL and/or channel number flashing | |
| − | + | #Select desired channel number with up/down and press [AB/ENTER] to save to memory | |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
NOTE: If channel number is blinking, that channel has been previously programmed and will be overridden. | NOTE: If channel number is blinking, that channel has been previously programmed and will be overridden. | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
== External Resources == | == External Resources == | ||
* [http://www.miklor.com/UVB5/UVB5-ProgMem.php] | * [http://www.miklor.com/UVB5/UVB5-ProgMem.php] | ||
Revision as of 17:54, 22 November 2015
programming
repeater offset and CTCSS
In this example will enter a 70cm repeater with PL and +5Mhz offset.
offset + or -
- Enter the VFO Mode
- Set offset [MENU] and arrow to item 21 (SFTP)
- Press [AB/ENTER] use arrow to select + and press [AB/ENTER] and [MENU], [MENU] to save
offset amount
- Press [MENU] and arrow to item 22 (OFFSET)
- Press [AB/ENTER] then enter the offset
- Press [AB/ENTER] and [MENU], [MENU] to save
PL / CTCSS
- Press [MENU] and arrow to item 12 (TCODE)
- Press [AB/ENTER] then enter the frequency in Hz
- Press [AB/ENTER] and [MENU], [MENU] to save
Enter and Save to channel
- key in desired frequency such as 442.400 for example
- Press and hold [VM/SCAN] until voice says MEMORY CHANNEL and/or channel number flashing
- Select desired channel number with up/down and press [AB/ENTER] to save to memory
NOTE: If channel number is blinking, that channel has been previously programmed and will be overridden.
