The following lines were added (+) and removed (-):
[[File:blackanddeckergrasshog720x340.jpg]]The charger is designed to use standard household 120 volt 60 Hz power.The charger is designed to use standard household 120 volt 60 Hz power. After normal usage, your power pack should be fully charged in 3 to 6 hours. If the power pack is run-down completely, it may take up to 6 hours to become fully charged.The charger and battery pack can be left connected with the red light glowing indefinitely. The charger will keepthe battery pack fresh and fully charged.NOTE: A battery pack will slowly lose its charge when kept out of the charger. If the battery pack has not beenkept on maintenance charge, it may need to be recharged before use. A battery pack may also slowlylose its charge if left in a charger that is not plugged into an appropriate AC source.=== Operation ===To turn trimmer on, pull the lock out button back and, then squeeze the trigger switch. To turnthe tool off, release the trigger. Slowly swing trimmer side-to-sideTo convert for maintenance edging, turn off the tool. Holding the trimmer with one hand by theauxiliary handle, grasp the collar and push in direction of arrow and rotate the trimmer head until it stops, (halfturn), release your hand, (rotate clockwise when viewed from the switch end). The tool is locked in the edgerposition. Rotate the wire edge guide forward and down into place before edging.Return to trimming position by turning the tool off, push in direction of arrow and rotating the trimmer headcounter clockwise until it stops. When using the tool in the trimmer mode you may choose to fold the wire edgeguide up out of the way.=== Line Feed ===Your trimmer uses .065” (1.65mm) diameter nylon line to cut grass and weeds quickly and easily. In time, the tip ofthe nylon line will become worn and the auto feed mechanism will automatically feed and trim a fresh length of line.The cutting line will wear faster if the cutting is done along sidewalks or other abrasive surfaces or heavier weedsare being cut. The automatic feed mechanism senses when more cutting line is needed and feeds and trims thecorrect length of line whenever it is required. You don’t even have to think about it. Do not bump unit on ground inattempt to feed line or for any other purpose.=== Spool Replace and Line Issues ===From time to time, especially when cutting thick or stalky weeds, the line feeding hub may become clogged with sapor other material and the line will become jammed as a result.To resolve a jam turn off the trimmer and remove the battery.# Press the release tabs on the line spool cover and remove the cover by pulling it straight off.# Lift the spool of nylon line out of the hub and clear any broken line or cutting debris from the spool area.3In case of jams and tangled line unwrap about one foot (30cm) of line to ensure that it is undamaged. If it is OKrewind it and insert the line end through the eyelet in the spool hub. Pull the line through thehole to maintain tension while placing the spool down into the hub with the notched side exposed.# Press the spool down GENTLY and rotate it until you feel it drop into place. (When in place, the spool will turn afew degrees left and right freely.)# Snap the spool cover back on, insert the battery and turn the tool on. In a few seconds or less you’ll hear the nylonline being cut automatically to the proper length.Bulk line for your trimmer/edger is available at extra cost from your local dealer or Black & Decker Service Center.To install bulk line, turn off the trimmer and remove the battery.# Press the release tabs on the line spool cover, and remove the cover by pulling it straight off.# Remove the spool from the tool and remove and discard all line on the spool.# Insert one end of the bulk line into the hole in the spool about 1/2” (12mm).# Hold the line in the hole and pull the rest of the line through the slot in the spool.# Snugly and evenly wind the bulk line onto the spool in the direction of the arrow on spool until it is nearly full. (The spool holds 50 ft. (15.2m) of line and bulk line is sold in 50 foot sections.)# Insert the line end through the eyelet in the spool hub. Pull the line through the hole to maintain tension while placing the spool down into the hub with the notched side exposed.# Press the spool down GENTLY and rotate it until you feel it drop into place. (When in place, the spool will turn a few degrees left and right freely.)# Snap the spool cover back on, insert the battery and turn the tool on. In a few seconds or less you’ll hear the nylon line being cut automatically to the proper length.[[File:blackdeckerinstalline.png]]== Parts and ServiceBlack and Decker NST2018 Type 1 18 Volt 12" Cordless GRASSHOG Trimmer / Edger Parts[[File:blackanddeckertrimmerparts.png]] [[Category:Outdoor Power Equipment]][[Category:Lawn and Garden]][[Category:Tangible Product]]